No-till Drill Parts & Equipment
Shop
-
2.5 inch. If you need taller pipes to improve gravity flow thru the secondaries, or just looking to replace rusted-out pipes or older pipes that lack dimples to redistribute seed & fertilizer more uniformly as it goes up into distribution head. Other sizes available. LEGACY P/N WAS SMA.Riser63.BLK – Riser pipe 2.5″ BLK$137.50
-
Atom-Jet seed boot/scraper (Case P-500/NH 2080, right or left). These carbide-protected replacement scrapers for the single shoot version of these drills are made from a long-lasting abrasion resistant plate to extend the life of the scrapers. The two sets of mounting holes allow for the scrapers to be adjusted up as the disk wears down.… Read More »Atom Jet Seed Boot/Scraper (Right)- Case IH P-500, NH 2080$139.00
-
LEGACY P/N WAS T 44A – STAR, replaceable bolt-on for T32TO, T32FL, & T44$56.37
-
Left Depth CONTROL Arm. Cast in Hi Tensile steel. The Hi Tensile stud is up sized for added strength where the stud leaves the casting.
$25.00 -
Right Depth CONTROL Arm. Cast in Hi Tensile steel. The Hi Tensile stud is up sized for added strength where the stud leaves the casting.$25.00
-
For John Deere 90 and Pro-series openers. The gauge wheel axle kit is the final piece in making your disc opener completely non-greasable! No more seized axles. Holds cast arms tight.$195.00
-
For John Deere 90 and Pro-series openers. The gauge wheel axle kit is the final piece in making your disc opener completely non-greasable! No more seized axles. Holds cast arms tight.$195.00
-
Includes replacement outer hub seal sleeve and inner hub seal sleeve to fit JD air seeder pro and non-pro series row units. Replaces JD N219000 and W33806.$6.75
-
Radial double taper roller bearing to fit JD 60/90/N series opener hub. Replaces JD bearing used in hubs: 60/90 series = AN281856 N series = AA97715 Timken or NTN brand only, not a cheap imitation!$77.00
-
Includes replacement outer hub seal to fit pro and non-pro series, and replacement inner hub axle spacer seal to fit all non-pro series, and pro series prior to s/n 795300 (or spacer used with replacement greaseless axle kit installation on pro series). Replaces JD B13294 and AN281241. **Does not include direct replacement for JD A114711 OEM seals used on s/n 795301+ pro series axle tube nut**$10.80
-
For JD 90-series boots. Patented, simple, bolton device designed to fit between the main opener arm boot pivot flanges and the seed boot, eliminating the up and down movement of the seed boot and allowing for a consistent furrow and more even seed placement. Includes necessary hardware & new seed boot pivot pin.
$40.00 -
For 50-series boots. Patented, simple, bolton device designed to fit between the main opener arm boot pivot flanges and the seed boot, eliminating the up and down movement of the seed boot and allowing for a consistent furrow and more even seed placement. Includes necessary hardware & new seed boot pivot pin.
$40.00
All About Hydraulic Oil Coolers & Snorkel Kits
Stay cool; prevent clogging
Hydraulic oil coolers function by circulating oil through a radiator connected to a fan, which forces air over the radiator. This process cools the hydraulic oil while simultaneously warming the air entering the lines, helping to prevent clogging from sticky fertilizers and seed treatments.
When run with a snorkel, it helps remove humidity by pulling drier air from higher up, which is also cleaner air, so you reduce the amount of dust and debris that could cover the radiator. Snorkel kits are available with or without the oil coolers, for air carts and air boom applicators.