Aricks Bushing Kits
- $80.20Kit-Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Air Hammer LEGACY P/N WAS ARI 003A - Updated Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Air Hammer$175.42Kit-Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Manual Tool Manual removal tool for the bushings of the front/main pin of JD 50/60/90 drill openers. Use this to pull the bushings out. Kit includes stainless tube brush to clean out dirt and rust. Also includes lubricant. FOR USE WITH IMPACT WRENCH LEGACY P/N WAS ARI 003M - UPDATED Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Manual Tool$48.00Sleeve, bushings & seals for closing arm's pivot, JD 50/60/90 drills (excluding earliest 750s). Chromed steel sleeve is 86mm long for 50/60/90s (doesn't fit the earliest 750s).$45.00
Chromed sleeve, bushings, and seals for firming arm's pivot, JD 60/90 drills. Chromed steel sleeve is 62mm length for 60/90-series. (The 50-series requires a different length of sleeve; see the kit ARI.NG69)
$45.00Chromed sleeve, bushings, and seals for firming arm's pivot, JD 750 & 1850 drills (doesn't fit the earliest 750s). Chromed steel sleeve is 69mm version for the 750s and 1850s. Note: The 50-series firming arm has the pin welded into it—you'll need to cut this off of the arm and bore a hole in that spot for a 5/8" bolt.$44.00Bushings and pin for front/main pin (where opener attaches to rockshaft clamp), JD 50/60/90 drills.$45.00Install tool for firming & closing kits
$45.00Removal tool for firming & closing kits
$4.68Grade 8 washer (special ID) and grade 8 special flange locknut (smooth underside; no serrations) for closing arm pivot point, JD 50/60/90 drill. Corresponding OEM parts are only grade 5, and wear out fairly quickly, which creates side-play and lets the spring for the closing arm pop out of its setting too easily.All About Bushing Kits
Keeping the firming and closing arm pivots working properly can be a real hassle on the JD 50/60/90 drills. Even after Deere upgraded them circa 2009 to include seals, they still have a habit of packing full of dirt and not taking grease. But with the Aricks bushing kits from Australia, these pivots will run smoothly and you’ll never have to grease them again! The Aricks seals for the firming & closing pivots have a Teflon coating on the seal contact lip and are designed to run dry, unlike a competitor product from USA — and these Aricks kits have an extensive track-record since ’09 proving their durability and trouble-free nature. The bushings themselves are fiber-wound Teflon impregnated, and the steel sleeve has a hardened chrome finish, for smooth action, and proven to last at least as long as OEM (significantly longer in some conditions). These kits are hugely popular in Australia.
Note: On 50-series,* the firming arm has a pin welded in – this must be removed and a hole drilled in the arm at that spot, and requires a 50-series bushing kit as the sleeve length is longer than the 60/90-series.
*Doesn’t fit the earliest 750s.
Aricks Main Opener Pin Kit
The main pin & bushings at the front of the opener on the JD 50/60/90 drills (where the arm attaches to the rockshaft) is another wear item, and it’s critical to maintain furrow width. If these get sloppy, the furrow gets narrower and the boot and firming wheel no longer fit, and seed placement is awful. The first time around, simply rotate the pin by 180-degrees (loosen the bolt locking it in position; put a pipe wrench on the end of the pin). If this has already been done, and they’ve gotten sloppy again, the next step is to replace pins & bushings. Aricks’ main pin kits have been in the field since 2013, and proven to last at least as long as OEM in tough Aussie conditions, and sometimes significantly longer. Aricks front pin bushings are steel with a Teflon inner layer, and the pin has a hard chrome finish. Whether merely turning the pins, or doing a complete rebuild, be sure to retorque the retaining bolt to spec when finished; inadequate torque can result in the bushings spinning in the opener arm, ruining it.
“After 8 years & 20,000 acres: “They [the firming & closing bushing kits] were good the whole way through. I never had any problems with them at all. I would recommend them to anyone.”Ed WhitechurchTemora, NSW, Australia, (30’ JD 1890Aricks Bushing Kits Videos
About Aricks Opener Main Pin KitHow to Install Aricks Bushing Kits on John Deere 60/90 No-till DrillsHow to Install Aricks Opener Main Pin Kit on John Deere 50/60/90 No-till DrillsContent of this page is copyright 2005-2024 Exapta Solutions, Inc. (reprint with written permission only).
Thompson wheel covered by U.S. Patent No. 6,907,833. Liquid delivery feature of Valion seed tube guards is U.S. Patent No. 8,978,564. Ninja seed bounce flap U.S. Patent Pending. UniForce U.S. Patent Pending. All rights reserved on other designs. Exapta is a registered trademark of Exapta Solutions, Inc. Keeton is a registered trademark of Precision Planting. Mojo Wire, Thompson wheel, Valion guard, Ninja flap, UniForce, DuraLok, No-till Seeding Explained, and No-till Seeding School are trademarks of Exapta. Disclaimer: Recommendations & page content are current, accurate, and believed to be broadly applicable as of the time of writing (Dec 2005) and last update (2005 – 2014). Because of diversity of soils, climate, crops, planter & drill models/designs marketed worldwide, combinations of attachments, etc., actual results may vary. No warranty is made as to actual results obtained. Should you encounter exceptions or worthwhile annotations to the statements made on this page, please contact us.
“We rebuilt the drill this year and it’s been extremely impressive on the rebuild. We put on the better blades [Forges de Niaux], DuraLok firming wheels and the Aricks Main Pins/Bushings. We got to noticing our seed slot was getting very narrow and we just happened to receive one of your flyers that addressed that. We had a lot of slop in those bushings. We planted about 700 ac of soybeans this year and we are getting the best stands we’ve ever seen with this drill. I am very impressed with your products! We don’t mind running this older equipment if you can make it work. You guys [Exapta] have figured out some stuff that other companies haven’t yet. And, your service has been excellent. You have helped us out a lot.”
Jason PetersCarthage, MO, Exapta customer since 2013 (JD 1560, 15ft on 7.5”)“So far I think our best decision has been the bushing kits. I installed them all last spring and have not had one row give me any problems! I love not having to grease 104 fittings! Keeping the press arm and closing arm free of seizing up makes everything else work on these 90 series openers.”
Kory HastingsGreat Falls, MT, Exapta customer since 2017 (Duraloks, Ninja flaps, T-whls, bushing kits on JD 1895 43ft with a 1910 TBH cart)Derek Tjaden
Derek is Kansas native who grew up in a 100% no-till farming operation. From an early age the benefits of no-till were made known to Derek by his father and by attending no-till conferences. From there he furthered his passion for soils while at Kansas State University getting his agronomy degree. He has had the experience of working in various roles and sectors of agriculture from sales and consulting, to management, which have all been within production agriculture. Derek has also worked in specialty ag markets such as turf and ornamentals.
Bob Pagel
Sales & Service Representative
Prior to joining Exapta, Bob Pagel was an Agricultural Territory Sales Manager for Ritchie Brothers, serving parts of MN, WI and IA. He continues to support his family farm in SE Minnesota.
Jon Zeller
Current Product Engineer
Jonathan Zeller joined Exapta excited to return to working with no-till planting equipment. He supported research of no-till planting and other ag related projects for 7 years with Kansas State University’s Agricultural Engineering Department after getting his engineering degree. He later worked 3 years for Landoll Company, LLC. where he gained experience in a design engineering role. Jonathan grew up on a small family farm in NE Kansas working with row crops, hay and cattle. Jonathan enjoys solving engineering problems and improving or creating products to be robust and easy to install and service.
